advantageterew.blogg.se

1. #PHOENIX RC HELICOPTER SIMULATOR INSTALL#
2. #PHOENIX RC HELICOPTER SIMULATOR SERIAL#
3. #PHOENIX RC HELICOPTER SIMULATOR MANUAL#
4. #PHOENIX RC HELICOPTER SIMULATOR SOFTWARE#
5. #PHOENIX RC HELICOPTER SIMULATOR PC#

ATI Radeon 9800/NVidia Geforce Ti4200 with at least 128MB memory or better.1.5 GB free, uncompressed hard-disk space.

Microsoft Windows XP, Windows Vista, Windows 7 or Windows 8 operating system.

#PHOENIX RC HELICOPTER SIMULATOR PC#

#PHOENIX RC HELICOPTER SIMULATOR SOFTWARE#

Thank you!ġ x Simulator Software DVD(other accessories demo in the picture is not included.Technical NotesTo successfully use Phoenix, you will need the following:

pls make sure you do not mind before you bid.ĭue to the difference between different monitors, the picture may not reflect the actual color of the item.

#PHOENIX RC HELICOPTER SIMULATOR MANUAL#

Please allow 1-2cm error due to manual measurement. Powered by computer USB, no battery required This is a remote control flight simulator connected to a computer,Not radio.ĭoes not support physical remote control aircraft is also a need to practice slowly, or not touch on the practice of. It should be reminded that the simulation is difficult, and the same real machine, and would like to fly a helicopter to hover or flight, etc. Grounded and can also modify the simulator in the relevant parameters, such as adjusting the gyro sensitivity and so on, in order to achieve the best helicopter flight. such as the helicopter took off too heavy, please point "model", and then point "physical parameters of change," the weight of the helicopter into a 1 kg less, it would be more close to real machine sensitivity. a good XTR software installed, open the software, point the top of the directory bar "remote control" and then point the pop-up "channel distribution", the channel is set above diagram, the signal can not be set if there is no channel allocation, then replace the computer's USB interface else is even trying.ģ.channel settings - Select a helicopter model (the oil machine is also OK), and then will simulate all the fine-tuning the remote control center, will throttle the most significant pull away several times under the pole (not such action would lead to "calibrate neutral position" when the throttle item can not be neutral, and thus can not be a normal takeoff), and then placed in the middle of the throttle rod, after the computer software catalog column "remote control" below to find out "calibration neutral position" calibration, calibration, simulation start after the completion point - check to see which channels do not (all around the hem tail, tune into a real machine, such as the same direction as the control) - if so, what channel do not, then the return channel settings that will control the right side of the channel "+" to "-" ( or vice versa), as indicated in figure on the right to re-calibrate icon - channel settings are correct, you can begin to play a!Ĥ. After running Simulator Switcher to select the software name, run G7.0 or Phoenix 5.0 XTRġ.in order to XTR as an example: steps can not be wrong! Pull the analog switch to XTR logo Department, will simulate remote-controlled USB lint plug into your computer, then open the simulated remote control power switch, this time the remote control power lantern kept flashing (if not switched on, the computer interface, no, need to Another change computer interface, the operation sequence above still need to operate once).Ģ. Or switch the switch in the lower right corner of the USB emulator handle - four sliding gears for you to choose.Ĥ. Run the "SimLauncher2017.exe" simulator console as administrator in CD, and change to different program more easily and conveniently.

#PHOENIX RC HELICOPTER SIMULATOR INSTALL#

Before run any program, pls install the "DirectX9.0" in CD.ģ. Firstly try to find the "autorun" icon in CD, this is quick installation guide.Ģ. (32 bits, 64bits) XP, Windows7, Windows8, Windows10, Vistaġ. Phoenix 5.0 supports on-line upgrading.Ĥ.

#PHOENIX RC HELICOPTER SIMULATOR SERIAL#

G7.0 one key installation, equipped with Real RF7 G7/ G6.5 (the only serial number).